Solidworks Insert Drawing View Normal to Plane

Standard Shortcuts
Shortcut Description More Information...
Tab

With an initial object selected in the design, extend the choice to include the side by side higher-level object (or objects), based on logical hierarchy.

In add-on, the feature caters for selection extension across multiple objects selected across different nets in the design.

Control Page
Shift+Tab

Single select the next design object in a set of co-located (overlapping) objects without utilizing a selection pop-upwardly window

To apply this control, ensure that the Display popup selection dialog selection is disabled on the PCB Editor - General folio of the Preferences dialog.

Command Page
Shift+Ctrl+X Enable Cross Select Style Command Page
Ctrl+A Select all objects on the electric current document Control Folio
Ctrl+B Select all objects that reside within the purlieus of the defined board shape Control Page
Ctrl+H Select all electrical objects that are connected to the aforementioned slice of copper Command Page
Ctrl+R Re-create selected object(s) and paste repeatedly where needed in the workspace (safe stamping) Command Page
Alt+Insert Paste objects onto the current layer regardless of their original layer assignments Command Folio
Shift+Ctrl+L Marshal selected objects by their left edges Control Page
Shift+Ctrl+R Marshal selected objects by their right edges Control Page
Alt+Shift+Fifty Align selected pattern objects by their left edges while maintaining acceptable spacing in observance with applicable design rules Command Page
Alt+Shift+R Align selected design objects by their right edges while maintaining adequate spacing in observance with applicable design rules Command Page
Shift+Ctrl+H Brand the horizontal spacing of selected objects equal Control Page
Shift+Ctrl+T Align selected objects by their top edges Command Folio
Shift+Ctrl+B Align selected objects past their bottom edges Command Folio
Alt+Shift_I Align selected design objects past their top edges while maintaining adequate spacing in observance with applicable design rules Command Page
Alt_Shift_N Align selected design objects by their bottom edges while maintaining adequate spacing in observance with applicable design rules Command Page
Shift+Ctrl+V Make the vertical spacing of selected objects equal Command Page
Shift+Ctrl+D Move selected components to the nearest indicate on the required component placement grid Control Page
Ctrl+Habitation Motion the cursor to the absolute origin at the lower-left corner of the workspace Control Page
Ctrl+Finish Motility the cursor to the relative origin of the electric current document (PCB document), or the location of the component reference point (PCB Library document) Command Page
Ctrl+Q
  • In the workspace to admission the Selection Memory dialog, from where yous can control all aspects of the choice memory feature
  • In a dialog or panel to toggle the measurement units (in the dialog or console just), between metric (mm) and purple (mil)
Command Folio
Ctrl+n (north = 1 to eight) Shop the electric current pick in memory location n Command Page
Alt+n (n = ane to eight) Recall the selection from retention location due north Command Folio
Shift+n (north = ane to 8) Add the current selection to the pick already stored in memory location n Command Folio
Alt+Shift+north (n = 1 to 8) Recall selection from retentivity location n and add together information technology to the current selection in the workspace Command Page
Shift+Ctrl+due north (n = 1 to 8) Apply filtering based on the pick set in memory location n Control Page
Shift+A ActiveRoute selected connections Command Page
Shift+F Access the Discover Like Objects feature (click on an object to use every bit the base template) Command Folio
i Switch the display of the PCB workspace to Board Planning Mode Control Page
2 Switch the display of the PCB workspace to second Layout Mode Command Page
iii Switch the display of the PCB workspace to 3D Layout Way Control Page
Ctrl+Alt+ii Switch the display of the PCB workspace to 2d Layout Way  and encounter the same location and orientation of the board as you switch. Control Page
Ctrl+Alt+3 Switch the display of the PCB workspace to 3D Layout Mode and meet the aforementioned location and orientation of the board equally y'all switch. Command Page
Ctrl+PgDn Brandish all design objects on the electric current document Command Page
PgUp Zoom-in, relative to the current cursor location.

You can likewise use the mouse to zoom in to a region of the document by 1 of the following methods (where applicable and depending on how the buttons of your mouse might be assigned):

  • Hold the Ctrl key and roll the mouse wheel upward. Use of the Ctrl fundamental is a default setting that can be changed from the System - Mouse Wheel Configuration page of the Preferences dialog.
  • Concord both the Ctrl key and the right-mouse button, and so motion the mouse frontward.
  • Hold the right (kickoff) and left (2d) mouse buttons, and then move the mouse forward.
  • Click and hold the mouse cycle, then motility the mouse forward.
Command Folio
PgDn Zoom-out, relative to the electric current cursor location.

You tin utilise the mouse to zoom out from a region of the document by 1 of the following methods (where applicable and depending on how the buttons of your mouse might be assigned):

  • Hold the Ctrl key and roll the mouse bike down. Use of the Ctrl key is a default setting that can exist changed from the System - Mouse Wheel Configuration folio of the Preferences dialog.
  • Hold both the Ctrl key and the right-mouse push button, then move the mouse backward.
  • Hold the right (commencement) and left (second) mouse buttons, then move the mouse backward.
  • Click and agree the mouse wheel, then move the mouse backward.
Control Folio
Shift+PgUp Zoom-in, relative to the electric current cursor location and in progressively smaller steps Control Page
Shift+PgDn Zoom-out, relative to the current cursor location and in progressively larger steps Command Page
Ctrl+PgUp Set the magnification of the current document to 400% Command Page
Mouse Cycle Scroll vertically inside the design workspace. This is a default setting that can be changed from the Organization - Mouse Wheel Configuration page of the Preferences dialog -
Shift+Mouse Wheel Scroll horizontally within the blueprint workspace. This is a default setting that tin exist changed from the System - Mouse Bike Configuration page of the Preferences dialog -
Dwelling Redraw the view in the master design window, placing the location marked by the cursor - prior to launching the command - at the center of the window Control Page
Terminate Refresh the screen, in effect performing a redraw of the current certificate, to remove whatsoever undesirable drawing update furnishings Command Folio
Alt+Left Pointer

Jump to, and make active, the previous component in the current library document

Later on reaching the starting time component in the listing, the command will not cycle to the last component once more.

Control Page
Alt+Right Pointer

Jump to, and make active, the next component in the current library document

Later on reaching the last component in the listing, the command will non cycle to the first component again.

Command Folio
Alt+Stop Redraw the current layer of the current document, to remove any undesirable drawing update effects Control Page
Alt+F5 Toggle the display of the current certificate'south editor between maximized and non maximized Command Folio
F5 Visually toggle the Net Color Override characteristic on or off Command Page
Shift+H Toggle the Heads Upwards Display on or off Command Page
Shift+One thousand Toggle Heads Upwardly Display tracking on or off Command Page
Insert Resets the Delta Origin indicate for the Heads Up Display characteristic to 0,0 Command Page
Shift+Z Toggle the 3D model visibility in the current PCB document Command Page
Shift+D Toggle the brandish of the Delta coordinates within the Heads Up Display Command Page
Shift+E Cycle to the next mode of object Hotspot Snapping Control Page
Ctrl+Chiliad Access the dedicated grid editor dialog for the snap grid currently nether the cursor Command Page
Shift+Ctrl+Yard Set the Ten (horizontal) and Y (vertical) step values - for the default Global Board Snap Grid - simultaneously to a called value Command Page
Q Toggle the measurement units for the electric current document between metric (mm) and majestic (mil) Command Page
Shift+O

Toggle the display of the Departure Map Overlay in the main design workspace On or Off

This command is available just provided a comparing has been performed from the Interact, Compare and Merge panel.

Command Folio
F6 Toggle the state of the current cell containing detected differences betwixt checked and unchecked when using Altium Designer's Collaborative PCB Design functionality (where a comparison has been performed from the Collaborate, Compare and Merge console) Command Folio
F7 Navigate to the previous jail cell containing one or more detected differences when using Altium Designer's Collaborative PCB Blueprint functionality (where a comparing has been performed from the Interact, Compare and Merge console) Command Folio
F8 Navigate to the adjacent cell containing one or more detected differences when using Altium Designer's Collaborative PCB Pattern functionality (where a comparing has been performed from the Collaborate, Compare and Merge console) Command Folio
L Admission the Layers And Colors tab of the View Configuration panel in which y'all tin configure the display of layers for the board and the colors assigned to those layers Control Page
Ctrl+D Admission the View Options tab of the View Configuration panel in which yous can configure the mode used to brandish each of the various blueprint items within the workspace Control Page
Shift+V Admission the Board Insight popular-up, listing all violations (of divers Pattern Rules) currently under the cursor Command Page
Shift+X Access the Lath Insight pop-upward, listing all components and/or net objects currently under the cursor Command Page
Ctrl+M Measure and display the distance between whatever two points in the electric current document Command Page
Left Arrow Motion the cursor to the left in the current document workspace in increments of one snap grid unit Control Page
Shift+Left Arrow Move the cursor to the left in the current certificate workspace in increments of 10 snap grid units Command Page
Correct Arrow Movement the cursor to the right in the electric current certificate workspace in increments of one snap grid unit Command Page
Shift+Right Arrow Motion the cursor to the right in the electric current document workspace, in increments of x snap grid units Command Page
Upwards Arrow Movement the cursor up in the electric current document workspace, in increments of one snap grid unit Command Folio
Shift+Up Arrow Move the cursor upwards in the current document workspace, in increments of 10 snap grid units Command Page
Down Arrow Motion the cursor downwards in the electric current document workspace, in increments of 1 snap grid unit Control Folio
Shift+Down Arrow Move the cursor downwardly in the electric current certificate workspace, in increments of 10 snap grid units Control Page
Ctrl+Left Arrow Motion the current pick (one or more than selected design objects) to the left in the current document workspace in increments of one snap grid unit Command Page
Shift+Ctrl+Left Arrow Move the current selection (one or more selected design objects) to the left in the current certificate workspace, in increments of 10 snap grid units Control Page
Ctrl+Correct Pointer Motion the current selection (one or more than selected design objects) to the correct in the current document workspace, in increments of 1 snap grid unit Command Page
Shift+Ctrl+Right Arrow Motion the electric current selection (one or more selected pattern objects) to the right in the current document workspace, in increments of x snap grid units Command Folio
Ctrl+Upwards Arrow Move the electric current selection (ane or more selected design objects) upwards in the current certificate workspace, in increments of one snap grid unit Control Page
Shift+Ctrl+Up Arrow Move the current option (one or more selected design objects) up in the current document workspace, in increments of 10 snap grid units Command Folio
Ctrl+Downward Pointer Move the electric current selection (one or more than selected pattern objects) downward in the electric current certificate workspace, in increments of one snap grid unit of measurement Command Page
Shift+Ctrl+Downwards Arrow Motion the electric current option (ane or more selected design objects) downwards in the current document workspace, in increments of 10 snap filigree units Command Folio
Shift+Click Change the option status of the object currently under the cursor without affecting the status of other objects Command Folio
Click Select/deselect the object currently under the cursor Control Page
Ctrl+Click
  • On a net object to highlight the entire routed net
  • On a layer tab to highlight all content on that layer
  • In free infinite to clear current highlighting
-
Shift+Ctrl+Click
  • On a cyberspace object to highlight the entire routed net in addition to the routed nets already highlighted (cumulative routed cyberspace highlighting)
  • On a layer tab to highlight all content on that layer in addition to the content already highlighted on other layers (cumulative layer highlighting)
-
Alt+Click On a connection to select that connection -
Alt+Shift+Click On a connection to select that connection in addition to the connections already selected (cumulative connection selection) -
Alt+Click&Drag (from right-to-left) To select all connections touched by the dragged rectangle -
Alt+Ctrl While hovering the cursor over a layer tab to highlight the content of that layer but -
Shift+Ctrl+Click&Hold Create a vertex (or break) in a track segment at the current cursor position Command Page
Double-Click Modify the properties of the object currently nether the cursor Control Page
Click (on an object), Hold&Elevate Move the single object currently nether the cursor (or group of selected objects if the object is function of that selection) Control Page
Click (away from objects), Hold&Drag (left-to-right) Select all objects that fall completely within the premises of the selection area Command Page
Click (away from objects), Concord&Drag (right-to-left) Select all objects that fall completely inside the selection area or are touched by its boundary Command Page
Right-Click, Hold&Drag Brandish the slider (panning) manus cursor then drag to movement your view of the workspace Command Page
Right-Click Access context menu for workspace or object currently under the cursor. If currently within an interactive command, volition escape from the current operation -
F11 Toggle the display of the Properties panel appropriately -
F12 Toggle the brandish of the PCB Filter console or the PCBLIB Filter panel appropriately -
Shift+F12 Toggle the brandish of the PCB List console or the PCBLIB Listing panel accordingly -
Shift+C Clear the filter that is currently existence applied to the agile certificate Command Page
Shift+Southward

Bike through the bachelor single layer viewing modes

The available modes are determined by enabling the corresponding options in the Bachelor Single Layer Modes region on the PCB Editor - Board Insight Display page of the Preferences dialog.

Control Page
+ (on the numeric keypad) Switch to the next enabled layer Command Page
- (on the numeric keypad) Switch to the previous enabled layer Command Page
* (on numeric keypad) Switch to the next enabled signal layer Command Page
Shift+* (on numeric keypad) Switch to the previous enabled bespeak layer Command Page
Backspace

Delete a single, selected terminate-of-route object (component-free track, arc, via, or pad). The singular routing object connected to the deleted object will be automatically selected and fix for subsequent deletion.

Past using the command repeatedly, you lot are able to incrementally unwind the routed path in the same way as using the Backspace shortcut while interactively routing.

Command Page
Ctrl+Delete

Delete one or more selected routing objects (component-gratis tracks, arcs, vias, and pads) on the current document. All routing objects continued to those deleted will be automatically selected and set for subsequent deletion

By using the control repeatedly, you are able to incrementally unwind the routed path in both directions.

Command Page
Alt+Ctrl+A Add a new comment thread to a defined area of the active certificate. Before yous tin can commencement using the comment feature, ensure that you have opened (checked out) a Managed Projection and are working on its PCB document Control Folio
Alt+Ctrl+P Add together a new comment thread to a specified point in the agile document. Before you can start using the annotate feature, ensure that y'all take opened (checked out) a Managed Project and are working on its PCB certificate Control Page
Alt+Ctrl+C Add a new comment thread to a selected component in the active document. Before you lot can kickoff using the annotate feature, ensure that you have opened (checked out) a Managed Project and are working on its PCB document Command Page
General Interactive Shortcuts

Note that the shortcuts bachelor will depend on the interactive command and the specific pattern object that is the focus of that command.

Shortcut Description
F1 Admission the Graphical Editing Hot key List dialog that provides a list of the shortcuts available (simply that cannot be launched) also every bit access to the documentation for the currently running command
Shift+F1 Admission a menu that lists all valid shortcuts for the nowadays stage of the currently running interactive command
Enter Acts similar a Click of the mouse when placing/moving an object
PgUp Zoom in
PgDn Zoom out
Terminate Refresh the screen
Dwelling house Change display to have the cursor (with the fastened object beingness placed/moved) at the center of the design window
Left Pointer Movement the cursor (with the attached object being placed/moved) to the left in the current document workspace in increments of i snap grid unit
Shift+Left Pointer Move the cursor (with the attached object beingness placed/moved) to the left in the electric current certificate workspace in increments of 10 snap filigree units
Right Arrow Move the cursor (with the fastened object existence placed/moved) to the right in the electric current document workspace in increments of 1 snap grid unit
Shift+Right Arrow Move the cursor (with the attached object being placed/moved) to the right in the current document workspace in increments of x snap filigree units
Up Arrow Movement the cursor (with the attached object being placed/moved) upward in the current document workspace in increments of ane snap grid unit
Shift+Upward Pointer Motion the cursor (with the attached object being placed/moved) upwards in the current document workspace in increments of 10 snap grid units
Down Arrow Move the cursor (with the fastened object being placed/moved) downwards in the current certificate workspace in increments of one snap filigree unit
Shift+Down Arrow Move the cursor (with the fastened object being placed/moved) downwards in the current document workspace in increments of 10 snap grid units
Tab Access the associated manner of the Backdrop panel in which properties for the object existence placed/moved tin can be inverse on-the-fly
Ten Mirror the object beingness placed/moved forth the X-axis
Y Mirror the object being placed/moved along the Y-axis
50 Flip the object existence placed/moved to the other side of the lath
Alt Constrain the management of movement to the horizontal or vertical centrality depending on the initial direction of motility
Shift When auto-panning while placing/moving an object, use to pan at higher speed
+ (on the numeric keypad) Switch to the next enabled layer
- (on the numeric keypad) Switch to the previous enabled layer
* (on numeric keypad) Switch to the next enabled point layer
Shift+* (on numeric keypad) Switch to the previous enabled signal layer
Esc Escape from the electric current procedure - either a phase of the currently running interactive command or the control itself
Spacebar Rotates the object being placed/moved counterclockwise. Rotation is in accordance with the value for the Rotation Step divers on the PCB Editor – General page of the Preferences dialog
Shift+Spacebar Rotates the object being placed/moved clockwise. Rotation is in accord with the value for the Rotation Step divers on the PCB Editor – General page of the Preferences dialog
North Toggle the display of the connection lines (ratsnest) while moving a component
, Click Cantankerous-probe from a called object on the current PCB certificate to its corresponding counterpart on the relevant schematic source certificate while remaining in the PCB document (Continuous Style)
, Ctrl+Click Cantankerous-probe from a chosen object on the current PCB document to its corresponding counterpart on the relevant schematic document, making the target schematic document the active certificate (Spring To Manner)
Concord Ctrl cardinal downwardly When moving a component to view dynamic alignment guides (green indicator lines) in relation to the boundaries of this and nearby components
Concord Shift key downwards When moving a component to view dynamic alignment guides (green indicator lines) in relation to the pads of this and nearby components
R When moving a component to cycle through component disharmonize resolution modes (Ignore Obstacles, Push Obstacles, Avert Obstacles)
Click&Elevate On a via in a stack of vias, use to move the unabridged stack to a new location
Ctrl+Click&Elevate On a via in a stack of vias, employ to move just that via to a new location (and not the entire stack)
Interactive Polygonal Object Shortcuts

The following additional shortcuts relate to placing/editing polygonal-shaped objects - Polygon Pour, Region, Coverlay Polygon, Polygonal Room, Extruded 3D Body, Board Shape.

Shortcut Clarification
Shift+Spacebar Bike through the five available corner modes (45 caste, 45 caste with arc, ninety degree, 90 caste with arc, and Any Angle) when placing a polygonal-based object
Spacebar Toggle between corner direction sub-modes (for the relevant corner modes) when placing a polygonal-based object
, Reduce the radius of the arc (by 1mil/0.025mm increments) when in arc cornering placement style
Shift+, Reduce the radius of the arc (by 10mil/0.254mm increments) when in arc cornering placement manner
. Increase the radius of the arc (by 1mil/0.025mm increments) when in arc cornering placement mode
Shift+. Increase the radius of the arc (past 10mil/0.254mm increments) when in arc cornering placement way
Ctrl+Click&Hold Anywhere along an edge of a selected polygonal-based object away from editing handles to insert a new end vertex
Click&Hold+Delete On an end vertex of a selected polygonal-based object, use to remove that vertex
Backspace Remove the last placed vertex
Interactive Routing Shortcuts
Shortcut Description
Tab Admission the Interactive Routing mode of the Backdrop panel in which you lot tin can change routing preferences on-the-fly, as well as alter backdrop of the track being placed
Shift+Spacebar

Cycle through the five available corner modes (45 caste, 45 degree with arc, 90 degree, ninety degree with arc, and Any Angle)

If the Restrict To xc/45 option is enabled on the PCB Editor - Interactive Routing page of the Preferences dialog, the arc cornering modes and the Whatever Angle mode volition not be available.

Spacebar Toggle between corner direction sub-modes (for the relevant corner modes)
, Reduce the radius of the arc (by 1mil/0.025mm increments) when in arc cornering placement mode
Shift+, Reduce the radius of the arc (by 10mil/0.254mm increments) when in arc cornering placement fashion
. Increase the radius of the arc (past 1mil/0.025mm increments) when in arc cornering placement style
Shift+. Increment the radius of the arc (by 10mil/0.254mm increments) when in arc cornering placement mode
Click or Enter Commits the routing upwardly to the current cursor position and places the tracks
Backspace Unwinds the last committed route back to its starting bespeak. If whatsoever objects had been pushed through placing the final segment, they are moved back to their original positions
Esc Terminates the current road. Any routing that has been committed earlier calling the termination is retained
Ctrl+Click Auto-complete segments to target
1 Toggle Look-Ahead placement mode on/off
Shift+R Cycle through the currently enabled routing conflict resolution modes. The modes available (including Walkaround Obstacles, Push Obstacles, Hug and Push Obstacles, Ignore obstacles, and Stop at First Obstacle) can be defined on the PCB Editor - Interactive Routing page of the Preferences dialog and modified on-the-fly (printing Tab to access the Interactive Routing mode of the Properties panel)
v Toggle Follow Mouse Trail manner
Shift+D Toggle automatic loop removal characteristic on/off
Ctrl+W Toggle the brandish of clearance boundaries
Shift+W Choose the required rails width from available predefined favorite routing widths in the Track mode of the Properties panel
Shift+Five Choose the required via size from bachelor predefined via sizes, sourced from one or more associated via templates using the Choose Via Sizes dialog
three

Wheel through routing width sources (User Selection --> Dominion Minimum --> Rule Preferred --> Rule Maximum)

With

User Choice

, routing widths are defined and managed in the Favorite Interactive Routing Widths dialog.

4

Cycle through via size sources (User Choice --> Rule Minimum --> Rule Preferred --> Dominion Maximum)

With

User Choice

, via sizes are divers through via templates - locally to the agile PCB document or through associated Pad Via libraries (

*.PvLib

).

+ (on the numeric keypad) Switch to the next enabled (and rule-permitted) layer, dropping a via
- (on the numeric keypad) Switch to the previous enabled (and rule-permitted) layer, dropping a via
* (on numeric keypad) Switch to the next enabled (and rule-permitted) signal layer, dropping a via
Fifty

When routing from a multi-layer pad or via, switches the layer for the current connection to the next bespeak layer defined for that pad/via

This feature works simply when the routing is started from the pad/via and before the first segment is committed.

/ Add fanout via; tool immediately waits for next fanout to route and via to identify
2 Add a via without irresolute layer
half dozen Modify routing via start/cease layers
seven Cycles through the connections bachelor for routing if the electric current pad has multiple connections
ix Switches the cursor position from the currently selected pad or rail to the target pad or rails. If the location of the object being switched to is not in the current window, the view jumps and centers around the new cursor position
Shift+Ctrl+G Wheel Glossing Attempt way (Weak --> Strong --> Off)
Shift+C

Enable subnet swapping

If no swappable target subnets are available, a bulletin to this effect will be presented in the Letters console.

Shift+T Swap target subnet - cycles through all swappable target subnets
While interactively routing, you lot tin can enter LEGACY length tuning mode by using the Shift+A shortcut. The following additional shortcuts are bachelor within that fashion:
Shift+A End the squeeze box
Shift+M Toggle brandish of the length tuning gauge on/off
Click or Enter Commits the routing up to the current cursor position and places the tracks
Backspace Remove last segment or accordion
Esc Terminate current route. Whatsoever routing that has been committed earlier calling the termination is retained
Shift+R

Wheel through the currently enabled routing disharmonize resolution modes. The modes available (including Walkaround Obstacles, Push Obstacles, Hug and Push Obstacles, Ignore obstacles, and End at Commencement Obstacle) can be defined on the PCB Editor - Interactive Routing page of the Preferences dialog.

Shift+West Choose the required rail width from available predefined favorite routing widths in the Favorite Interactive Routing Widths dialog
Tab Access the Accordion manner of the Backdrop panel in which you lot can define the approach used for defining the target length and to change properties of the accordion pattern used in the tuning, on-the-fly
, Decrease the aamplitude of the accordion pattern by the amount defined for the Amplitude Increment in the Squeeze box mode of the Backdrop panel
. Increment the aamplitude of the accordion blueprint by the amount defined for the Amplitude Increment in the Accordion mode of the Properties panel
ane Decrease the corner (miter) radius (when using the Mitered with Lines or Mitered with Arcs squeeze box patterns)
2 Increase the corner (miter) radius (when using the Mitered with Lines or Mitered with Arcs accordion patterns)
3 Decrease the gap (pitch) for the accordion pattern by the amount defined for the Gap Increment in the Piano accordion mode of the Backdrop console
four Increase the gap (pitch) for the accordion pattern by the corporeality divers for the Gap Increase in the Squeeze box mode of the Backdrop console
P Cycle forwards through the supported tuning patterns. Available patterns are: Mitered with Lines, Mitered with Arcs, and Rounded
Shift+P Cycle backward through the supported tuning patterns. Bachelor patterns are: Mitered with Lines, Mitered with Arcs, and Rounded
Y Toggle Amplitude Direction (starting direction) for the accordion blueprint
Interactive Differential Pair Routing Shortcuts
Shortcut Description
Tab Admission the Differential Pair Routing mode of the Properties console from where you can change routing preferences on-the-wing, too as modify properties of the rail being placed
Shift+Spacebar

Bicycle through the four available corner modes (45 degree, 45 caste with arc, xc caste, xc caste with arc)

If the Restrict To xc/45 choice is enabled, on the PCB Editor - Interactive Routing folio of the Preferences dialog, the arc cornering modes will non be available.

Spacebar Toggle between corner direction sub-modes (for the relevant corner modes)
, Reduce the radius of the arc (by 1mil/0.025mm increments) when in arc cornering placement style
Shift+, Reduce the radius of the arc (past 10mil/0.254mm increments) when in arc cornering placement manner
. Increase the radius of the arc (past 1mil/0.025mm increments) when in arc cornering placement manner
Shift+. Increase the radius of the arc (by 10mil/0.254mm increments) when in arc cornering placement way
Click or Enter Commits the routing upwards to the current cursor position and places the tracks
Backspace Remove last segment
Esc Terminate electric current road. Any routing that has been committed before calling the termination is retained
Shift+R

Cycle through the currently enabled routing conflict resolution modes. The modes bachelor (including Walkaround Obstacles, Push Obstacles, Hug and Push Obstacles, Ignore obstacles, and Stop at First Obstacle) tin can exist defined on the PCB Editor - Interactive Routing page of the Preferences dialog, and modified on-the-fly (press Tab to access the Differential Pair Routing mode of the Properties panel)

When interactively routing differential pairs, the

AutoRoute On Electric current Layer

and

AutoRoute On Multiple Layers

modes are not available.

Shift+D Toggle automatic loop removal feature on/off
Ctrl+W Toggle the display of clearance boundaries
Shift+W Choose the required track width from bachelor predefined favorite routing widths in the Runway mode of the Properties panel
Shift+Five Choose the required via size from available predefined via sizes, sourced from one or more associated via templates. The Cull Via Sizes dialog volition announced with which to do so
3

Cycle through routing width sources (User Choice --> Dominion Minimum --> Dominion Preferred --> Dominion Maximum)

With

User Pick

, routing widths are defined and managed in the Favorite Interactive Routing Widths dialog. The rule-based values come from the applicable Differential Pairs Routing rule.

4

Bicycle through via size sources (User Choice --> Rule Minimum --> Dominion Preferred --> Rule Maximum)

With

User Choice

, via sizes are defined through via templates - locally to the active PCB document, or through associated Pad Via libraries (

*.PvLib

).

5 Wheel through available via patterns (aligned or staggered)
half-dozen Cycle through the divers Gap values available for the differential pair being routed, through the applicable Differential Pairs Routing rule (Min Gap --> Preferred Gap --> Max Gap)
Shift+B Cycle through the defined Width-Gap value pairings available for the differential pair being routed, through the applicable Differential Pairs Routing rule (Min Width-Min Gap --> Preferred Width-Preferred Gap --> Max Width-Max Gap)
+ (on the numeric keypad) Switch to the adjacent enabled (and rule-permitted) layer, dropping a via
- (on the numeric keypad) Switch to the previous enabled (and rule-permitted) layer, dropping a via
* (on numeric keypad) Switch to the next enabled (and rule-permitted) signal layer, dropping a via
L

When routing from a multi-layer pad or via, switches the layer for the current connexion to the adjacent signal layer defined for that pad/via

This characteristic works simply when the routing is started from the pads/vias and before the first segments are committed.

/ Add together fanout via, tool immediately waits for next fanout to road and via to place
ii Add a via without irresolute layer
Shift+C

Enable subnet swapping

If no swappable target subnets are available, a bulletin to this result volition exist presented in the Messages panel.

Shift+T Swap target subnet - cycles through all swappable target subnets
Shift+Ctrl+Yard Bicycle Glossing Effort mode (Weak --> Strong --> Off)
Interactive Multi-Routing Shortcuts
Shortcut Description
Tab Access the Interactive Routing mode of the Properties panel in which yous can change routing preferences on-the-fly, as well equally change properties of the bus routing existence placed
Shift+Spacebar

Cycle through the four available corner modes (45 caste, 45 caste with arc, xc caste, xc degree with arc)

If the Restrict To 90/45 choice is enabled on the PCB Editor - Interactive Routing page of the Preferences dialog, the arc cornering modes volition non be available.

Spacebar Toggle between corner direction sub-modes (for the relevant corner modes)
, Reduce the radius of the arc (by 1mil/0.025mm increments) when in arc cornering placement mode
Shift+, Reduce the radius of the arc (by 10mil/0.254mm increments) when in arc cornering placement mode
. Increase the radius of the arc (by 1mil/0.025mm increments) when in arc cornering placement way
Shift+. Increase the radius of the arc (past 10mil/0.254mm increments) when in arc cornering placement mode
Click or Enter Commits the routing up to the current cursor position and places the tracks
Backspace Remove last segments
Esc End electric current road. Whatsoever routing that has been committed earlier calling the termination is retained
Ctrl+Click Car-complete segments to target
Shift+R

Wheel through the currently enabled routing disharmonize resolution modes. The modes bachelor (including Walkaround Obstacles, Push Obstacles, Hug and Push Obstacles, Ignore obstacles, and Stop at Starting time Obstacle) tin be defined on the PCB Editor - Interactive Routing page of the Preferences dialog, and modified on-the-fly (press Tab to access the Interactive Routing manner of the Backdrop panel)

When interactively routing multiple traces, the

AutoRoute On Electric current Layer

and

AutoRoute On Multiple Layers

modes are non bachelor.

Shift+D Toggle automatic loop removal feature on/off
Ctrl+W Toggle the brandish of clearance boundaries
Shift+W Choose the required runway width from available predefined favorite routing widths in the Rails mode of the Properties panel
Shift+5 Choose the required via size from available predefined via sizes, sourced from one or more associated via templates. The Choose Via Sizes dialog will appear with which to practice so
3

Cycle through routing width sources (User Option --> Rule Minimum --> Rule Preferred --> Rule Maximum)

With

User Choice

, routing widths are defined and managed in the Favorite Interactive Routing Widths dialog.

4

Bike through via size sources (User Choice --> Dominion Minimum --> Rule Preferred --> Dominion Maximum)

With

User Pick

, via sizes are defined through via templates - locally to the active PCB document, or through associated Pad Via libraries (

*.PvLib

).

five Cycle through bachelor via patterns (aligned or staggered)
+ (on the numeric keypad) Switch to the next enabled (and rule-permitted) layer, dropping a via
- (on the numeric keypad) Switch to the previous enabled (and rule-permitted) layer, dropping a via
* (on numeric keypad) Switch to the next enabled (and rule-permitted) bespeak layer, dropping a via
L

When routing from multi-layer pads or vias, switches the layer to the side by side signal layer defined for those pads/vias

This feature works only when the routing is started from the pads/vias and before the first segments are committed.

/ Add together fanout via; tool immediately waits for next fanout to road and via to place
2 Add a via without changing layer
C Change the spacing between neighboring routes to use the Track-Rails clearance value divers in the applicative Clearance dominion
B Decrease the spacing between neighboring routes
Shift+B Increase the spacing between neighboring routes
Shift+Ctrl+G Cycle Glossing Effort manner (Weak --> Strong --> Off)
Interactive Length Tuning Shortcuts
Shortcut Description
Spacebar Bicycle forward through the supported tuning patterns. Available patterns are: Mitered with Lines, Mitered with Arcs, and Rounded
Shift+Spacebar Wheel backward through the supported tuning patterns. Available patterns are: Mitered with Lines, Mitered with Arcs, and Rounded
Shift+G Toggle display of the length tuning gauge on/off
Tab Access the Squeeze box fashion of the Backdrop panel in which y'all can define the approach used for defining the target length, and to change properties of the piano accordion blueprint used in the tuning, on-the-fly
, Decrease the amplitude of the accordion design by the amount defined for the Amplitude Increment in the Accordion mode of the Properties panel
. Increment the amplitude of the accordion pattern past the amount defined for the Amplitude Increment in the Accordion mode of the Properties panel
1 Subtract the corner (miter) radius (when using the Mitered with Lines, or Mitered with Arcs accordion patterns)
two Increase the corner (miter) radius (when using the Mitered with Lines, or Mitered with Arcs accordion patterns)
3 Subtract the gap (pitch) for the accordion pattern by the amount defined for the Gap Increment in the Accordion mode of the Properties panel
4 Increment the gap (pitch) for the accordion blueprint by the amount divers for the Gap Increment in the Piano accordion manner of the Backdrop console
Y Toggle Amplitude Direction (starting direction) for the piano accordion pattern
3D Body Placement Shortcuts

The shortcuts really available depend on the type of 3D Model existence placed or moved - Extruded, Cylinder, Sphere, or Generic 3D Model. Generic model back up includes Step ( *.Stp and *.Step), Parasolid (*.x_t and *.x_b (up to V27)), and SolidWorks formatted models. Support for SolidWorks and Parasolid format models, and the Parasolid format export, is enabled past installing the

SOLIDWORKS PCB Connector

extension. You lot will too crave an

MCAD Co-Designer - SOLIDWORKS (R)

license, which is enabled along with your regular Altium Designer license.

Shortcut Clarification
Tab Access the 3D Body fashion of the Properties console backdrop for the 3D body object being placed/moved can be changed on-the-fly
L Flip the 3D body object beingness placed/moved to the other side of the board
Northward Toggle the display of the connexion lines (ratsnest) while moving the 3D body for a component
X Mirror the 3D trunk object being placed/moved along the X-axis
Y Mirror the 3D body object being placed/moved along the Y-axis
eight (on numeric keypad)

Rotate the 3D torso object existence placed/moved counterclockwise effectually the model's 10-axis by 90°

This shortcut applies to Generic 3D Model and Cylinder model types only.

2 (on numeric keypad)

Rotate the 3D body object being placed/moved clockwise effectually the model's X-axis by 90°

This shortcut applies to Generic 3D Model and Cylinder model types only.

4 (on numeric keypad)

Rotate the 3D torso object existence placed/moved counterclockwise around the model's Y-centrality by 90°

This shortcut applies to Generic 3D Model and Cylinder model types only.

half dozen (on numeric keypad)

Rotate the 3D body object beingness placed/moved clockwise around the model's Y-axis by 90°

This shortcut applies to Generic 3D Model and Cylinder model types just.

Spacebar

Rotate the 3D trunk object being placed/moved counterclockwise around the model'south Z-axis by ninety°

This shortcut only applies to the Extruded model type when it is being moved.

Shift+Spacebar

Rotate the 3D torso object beingness placed/moved clockwise around the model's Z-axis past 90°

This shortcut simply applies to the Extruded model type when it is being moved.

nine (on numeric keypad)

Increase the Standoff Height for the 3D body object being placed/moved by ane Snap Filigree unit

This shortcut only applies to the Extruded model type when it is existence moved.

3 (on numeric keypad)

Decrease the Collision Height for the 3D torso object being placed/moved by ane Snap Grid unit

This shortcut only applies to the Extruded model type when it is existence moved.

3D Visualization Shortcuts

The following additional shortcuts are available when viewing the lath in 3D in the PCB Editor (or, where applicable, a component in 3D in the PCB Library Editor):

Shortcut Description More Information...
0

Change the view of the lath (or component) in 3D so that you are looking directly down from above (perpendicular) with zero rotation

In addition, y'all can use the applicable driblet-down field on the PCB Standard toolbar (PCB Editor), or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a fix of predefined 3D views when viewing your board (or library components) in 3D.

Command Page
ix

Change the view of the board (or component) in 3D so that you are looking straight down from above (perpendicular) with 90 Degree (clockwise) rotation in the 10-airplane

In addition, you can employ the applicable drop-down field on the PCB Standard toolbar (PCB Editor), or the PCB Lib Standard toolbar (PCB Library Editor) to rapidly choose from a gear up of predefined 3D views when viewing your board (or library components) in 3D.

Command Page
viii

Alter the view of the board (or component) in 3D so that you are looking at the lath from an orthogonal perspective

In addition, you can apply the applicable driblet-downward field on the PCB Standard toolbar (PCB Editor) or the PCB Lib Standard toolbar (PCB Library Editor) to quickly choose from a set of predefined 3D views when viewing your board (or library components) in 3D.

Command Folio
5 Toggle a lath that has flexible areas betwixt its flattened state (no Angle Line settings practical) and its folded state (all Bending Line settings applied) Control Page
Shift Access the 3D rotational sphere. With the sphere displayed, Right-Click and drag to change the orientation of the view -
Ctrl+C Copies the electric current view in the main blueprint workspace to the clipboard in bitmap format (*.bmp). You have command over the resolution of the copied paradigm via the 3D Snapshot Resolution dialog Command Page
Fifty Access the View Configuration panel in which you can configure how the board is rendered in 3D -
3D Measurements Shortcuts

The post-obit additional shortcuts are available when viewing the board in 3D in the PCB Editor and taking measurements using the Reports » Measure 3D Objects command:

Shortcut Clarification
Q

Toggle measurement units betwixt metric and imperial - the displayed measurement values volition update appropriately

Concord Ctrl key down

Equally you motility the cursor over a 3D object, use to select a specific face of that object

Shift+C

Clear all currently displayed measurements in the 3D workspace

Sub-Menu Shortcuts
Shortcut Gives Admission To...
A the Align sub-carte du jour
B the Toolbars sub-carte du jour
G a pop-upwards menu with Snap Grid commands
I the Component Placement sub-menu
J the Jump sub-menu
Thou the Panels sub-menu
M the Move sub-menu
N a pop-up menu of Connexion/Jumper display commands
O the right-click Options sub-menu
South the Select sub-carte
U the Route sub-menu
X the DeSelect sub-carte
Y the right-click Filter sub-carte
Z a pop-upwards menu with zoom commands

foutssperihat.blogspot.com

Source: https://www.altium.com/documentation/altium-designer/shortcut-keys?version=18.1

0 Response to "Solidworks Insert Drawing View Normal to Plane"

Enregistrer un commentaire

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel